The car’s ignition lock cylinder is an important mechanical part that allows you to start your vehicle. Each ignition lock is unique, and the key it provides lifts the inner pin so that the ignition can turn and jump.
Standard ignition lock cylinders are still common now in many trucks and car models used on road traffic. Often new cars are now fitted with a keyless starting system and have pushbuttons.
The ignition switch is installed inside the Chevrolet ignition lock cylinder. This electric component provides power to the vehicle, which causes the engine to turn and activates the starter motor. Before knowing how to remove ignition lock cylinder chevy without a key, let’s explore the basics:
What is an ignition lock cylinder?
An ignition lock cylinder is part of your car’s ignition switch. It connects to your key and provides the power necessary for starting your engine. An ignition lock cylinder may sport various shapes, designs, and colours depending on the type of vehicle it works inside.
Most of the ignition lock cylinders are located on the right of the steering column. There are generally four turning positions of these ignition locks as:
- Steering column unlock at the first position
- Releasing power to vehicle accessories at second position
- Turning on the fuel system and vehicle computer at third position
- Start of the engine at the fourth position
Structure of ignition lock
The ignition lock cylinder consists of tumblers and pins that prevent the vehicle from starting with the right keys. If the key is broken while driving, it isn’t easy to start the car.
Another possible feeling that sticks to the cylinder is either being in the ‘off position or running out, so you can’t turn the ignition off for some reason.
How to remove ignition lock cylinder chevy without a key?
The tumblers in a Chevy ignition lock cylinder may become worn out over time, or a key may break and find its way inside the ignition. Make sure that you remove the battery and then begin the ignition. If you need Chevrolet ignition locking replacement components, you must replace their assembly.
Steps to remove the ignition lock cylinder chevy without key
Disconnecting Battery
To open the hood, you need to remove the battery. You can find a series of positive and negative clamps holding the battery. These are put together with the help of nuts.
Take a wrench and remove bolts. Remove the only negative cable and leave the positive ones as it is. It is advised to keep the negative clamps far away from the battery to avoid any interference.
Locating Ignition Switch
Steering column cover as a decorative strip around the steering wheel hides the ignition switch. Refer to the vehicle manual to locate the exact location. Disable the steering gear using the steering column puller if it interferes with the ignition switch direction.
Now uncover the ignition box. The ignition key is located in the panel. If sealed by a plastic sheet, release the clip to remove the cover.
Remove Ignition Switch
Now, you are set to remove the ignition switch. Using a wrench, you can successfully disassemble the ignition switch easily. Make a hole using a power drill in the car’s ignition cylinder slot.
Clean out the dirt from the hole. Take a paper clip and straighten it. Place the clip inside the hole. Then place it on the left side of the ignition key lock cylinder. It will prevent the ignition key to start ‘on’.
Now insert the screwdriver into the cavity. Press it on the other side of a paper clip. Take out clip and screwdriver simultaneously along with sliding the switch out.
Installing new Ignition Switch
Locate the pin in the new ignition switch. Retaining the pin is crucial to avoid any twist from extending. Now retain the pin and move the new ignition switch towards the ignition module slowly. A sound of click validates the right placement of the ignition switch.
Test the switch
You must inspect the ignition switch before the ignition switch assembly. In case of a faulty ignition switch, it will be easier to deal with rather than complete the whole circuit.
Now reconnect the negative terminal to restore the power. Start the engine by sticking the key into the ignition switch. If the vehicle turns on without any problem, you replaced your ignition switch perfectly!
Replacing the ignition switch
The ignition switch is one of the car’s vital components since it provides the normal function of the car’s main circuit. Ward off ignition switches can prevent the car from running. The faulty ignition should be removed as soon as possible to ensure vehicle security.
The ignition key is located in the front or rear of the steering wheel. Each ignition switch comes with its unique key, which only works at this ignition switch. No worries, you can adjust the key without a switch. The broken switch must be removed. It is very simple to do this.
Ignition Lock Cylinder Chevy Signs
One common sign of a broken lock is the inability to turn the key or insert the key in the keyhole. Failure to start the engine and other sections of the vehicle is likewise a warning indicator for the failure of the locks. If the motor and electrical components fail, such as power cords or lights, the ignition locks may be damaged. If Toyota uses the model, the problem may be from the mechanical immobilizer and another quality anti-theft part of the vehicle. To have more confidence about the test of driving, it is critical to have deactivated the immobilizer of the Toyota.
How do I remove the ignition lock cylinder without key Dodge?
Dodge cars are fixed by retaining pins for ignition. This button will unlock the ignition to remove it from the cylinder. You won’t have your master key and must insert some bolt into it. Ensure to disconnect the battery for safe functioning and keep this ignition lock ON or off position as the pin is depressed. Remove steering wheel plastic to allow access to electrical switches as well as locks and switches. Depress the active retention lever to lock and remove the lock. Tie the latch back from the switch; it will quickly be disconnected from the ignition ring. Get rid of the key.
How do I remove the ignition lock cylinder without key Ford cars?
Eliminating an ignition lock cylinder without a key has the same instructions that have been written here. Remove the negative battery terminal to close to the airbag. Rearrange the new cylinder and reconfigure the tumblers of the new lock with that of the original key. The new bolt will require the former lock to be reassembled and match the new key to ensure it is easier to remove the ignition lock. Follow the procedures for deleting a Ford car key. Find all keys in the Ford car section. Return to the page that you’ve come from.
How do I remove the ignition lock cylinder without a key?
The ignition lock cylinder is a vital component of all engines. If you forget your key, you might not ever start your vehicle. We recommend calling the repair company or auto locksmith to get it removed. Consider all DIY actions only if a certified locksmith is not available. Disabling the battery is the very first important point of this tutorial. The spark in ignition cylinders is necessary to ignite the fuel and a compressed air mixture within the car’s engine. The removal of the wheels will allow you to access the cylinder more easily and replace the old one with a different wheel.
Is it possible to fix something at home?
A problem lock requires several specialised tools. These may be basic to complex tasks. If you don’t have both of the above factors, then it’s best to hire a mechanic to help with repair or rescue if there’s a problem on the way.
If you think it’s more important to check the instructions and practices of the manufacturer first or do something about it a few times. If you possess enough skills and knowledge relating to locks to handle them yourself, you can safely remove the lock without using any key.
Frequently Asked Questions
How do I turn my ignition switch on without the key?
The easiest way to turn the key is to use a screwdriver instead of the key. We’re not sure what kind of vehicle you have! If your door is locked, then it’s still possible that you can locate them with your screwdriver through the gap in the window or door.
If you have an ignition switch on your dash, press it before you turn the screwdriver.
How do I remove the ignition switch without a key?
Please remove the battery connections to ensure that there’s no power running through them. The easiest way is to keep the vehicle in the OFF position to access the wires easily under the steering wheel.
You can now take out your old cylinder manually or use a pick set tool.
Can I remove my ignition switch without a key?
Of course, you can! You have to press your car’s power button first to turn it off. It’s between the two ford keys on the top of the column, next to your windshield wiper fluid bottles.
There are 2 switches near your fuse panel inside the vehicle that will allow you to get started. Your car’s power switch will open the centre console latch, allowing you to press it and pop up your original ignition switch.
All of these methods do not require any key for complete removal!
How do I turn off the alarm on my Ford?
The best method is to remove the battery of your respective Ford. If you have a power switch under the dash, press it first. You can now pop out your original ignition barrel by hand.
If your car does not have one of these switches, remove the fuse panel behind the passenger seat and turn off your alarm with one of its switches.
Can you bypass an ignition lock?
Yes, you can bypass an ignition lock by keeping the car in the ON position. If your vehicle contains a keyhole on the dash, use a screwdriver instead of a key to turn it off first.
My Name is Christopher Angels, and I am a postgraduate in mechanical engineering. Cars have always excited me as a child, and soon I decided to dive into the world of cars by pursuing mechanical engineering. I also worked as a Mechanic for over 3 years to understand Cars’ anatomy and how each part contributes to its working.
My Name is Christopher Angels, and I am a postgraduate in mechanical engineering. Cars have always excited me as a child, and soon I decided to dive into the world of cars by pursuing mechanical engineering. I also worked as a Mechanic for over 3 years to understand Cars' anatomy and how each part contributes to its working.